my-prusai3-settings/Slic3r-Settings/printer/-prusa.ini

# generated by Slic3r 1.3.1-dev on 2019-06-06 13:38:06
bed_shape = 5x0,195x0,195x190,5x190
before_layer_gcode = 
between_objects_gcode = 
end_gcode = G91 ;rel Pos\nG0 Z20\nG90 ;abs Pos\nG1 F3000 X190 Y190\n\nM104 S145 ;temp lower
extruder_offset = 0x0
gcode_flavor = reprap
has_heatbed = 1
host_type = octoprint
layer_gcode = 
max_layer_height = 0.4
min_layer_height = 0.2
nozzle_diameter = 0.4
octoprint_apikey = 
pressure_advance = 0
print_host = octoprusa.iot-fra80
printer_notes = 
printer_settings_id = 
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 7
serial_port = 
serial_speed = 250000
start_gcode = G1 F2000 X50 Y100 Z5; start pos
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_set_and_wait_bed = 0
use_set_and_wait_extruder = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0
z_steps_per_mm = 0
slic3r: tweaked speeds, timelapse layer change g-code 2020-03-18 09:00:04 +00:00			`# generated by Slic3r 1.3.1-dev on 2019-06-06 13:38:06`
slic3r: new HW-config -> new bed size and added printrun settings dump 2015-09-17 13:01:04 +00:00			`bed_shape = 5x0,195x0,195x190,5x190`
slic3r settings 2015-09-13 20:27:34 +00:00			`before_layer_gcode =`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`between_objects_gcode =`
slic3r: new HW-config -> new bed size and added printrun settings dump 2015-09-17 13:01:04 +00:00			`end_gcode = G91 ;rel Pos\nG0 Z20\nG90 ;abs Pos\nG1 F3000 X190 Y190\n\nM104 S145 ;temp lower`
slic3r settings 2015-09-13 20:27:34 +00:00			`extruder_offset = 0x0`
			`gcode_flavor = reprap`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`has_heatbed = 1`
			`host_type = octoprint`
slic3r settings 2015-09-13 20:27:34 +00:00			`layer_gcode =`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`max_layer_height = 0.4`
			`min_layer_height = 0.2`
slic3r settings 2015-09-13 20:27:34 +00:00			`nozzle_diameter = 0.4`
			`octoprint_apikey =`
			`pressure_advance = 0`
slic3r: tweaked speeds, timelapse layer change g-code 2020-03-18 09:00:04 +00:00			`print_host = octoprusa.iot-fra80`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`printer_notes =`
			`printer_settings_id =`
faster speed, better first layer, shortcuts for slic3r 1.3 2018-11-30 11:53:59 +00:00			`retract_before_travel = 2`
slic3r settings 2015-09-13 20:27:34 +00:00			`retract_layer_change = 1`
			`retract_length = 1`
			`retract_length_toolchange = 10`
			`retract_lift = 0`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`retract_lift_above = 0`
			`retract_lift_below = 0`
			`retract_restart_extra = 0`
slic3r settings 2015-09-13 20:27:34 +00:00			`retract_restart_extra_toolchange = 0`
			`retract_speed = 7`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`serial_port =`
			`serial_speed = 250000`
tested slic3r settings for 0.3mm layer height 2015-09-14 15:09:19 +00:00			`start_gcode = G1 F2000 X50 Y100 Z5; start pos`
slic3r settings 2015-09-13 20:27:34 +00:00			`toolchange_gcode =`
			`use_firmware_retraction = 0`
			`use_relative_e_distances = 0`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`use_set_and_wait_bed = 0`
			`use_set_and_wait_extruder = 0`
slic3r settings 2015-09-13 20:27:34 +00:00			`use_volumetric_e = 0`
			`vibration_limit = 0`
			`wipe = 0`
			`z_offset = 0`
slic3r: new settings with v1.3 beta - more speed 2018-10-20 18:42:15 +00:00			`z_steps_per_mm = 0`