slic3r settings

Slic3r-Settings/filament/-prusa-noBed.ini

@@ -0,0 +1,17 @@
+# generated by Slic3r 1.2.9 on Sun Sep 13 20:59:03 2015
+bed_temperature = 0
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1.1
+fan_always_on = 0
+fan_below_layer_time = 30
+filament_colour = #0080FF
+filament_diameter = 3
+first_layer_bed_temperature = 0
+first_layer_temperature = 190
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
+slowdown_below_layer_time = 10
+temperature = 190

Slic3r-Settings/filament/JB-190-bed_0-fan_on.ini

@@ -0,0 +1,17 @@
+# generated by Slic3r 1.2.9 on Sun Sep 13 14:18:26 2015
+bed_temperature = 0
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 30
+filament_colour = #0080FF
+filament_diameter = 3
+first_layer_bed_temperature = 0
+first_layer_temperature = 190
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
+slowdown_below_layer_time = 10
+temperature = 190

Slic3r-Settings/filament/JB-190-bed_65_60.ini

@@ -0,0 +1,16 @@
+# generated by Slic3r 1.2.6 on Wed May 20 21:08:43 2015
+bed_temperature = 60
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 0
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 30
+filament_diameter = 3
+first_layer_bed_temperature = 65
+first_layer_temperature = 190
+max_fan_speed = 100
+min_fan_speed = 30
+min_print_speed = 10
+slowdown_below_layer_time = 10
+temperature = 190

Slic3r-Settings/print/-prusa-h03f30.ini

@@ -0,0 +1,86 @@
+# generated by Slic3r 1.2.9 on Sun Sep 13 21:35:21 2015
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 2
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 0
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 30%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_speed = 75%
+gap_fill_speed = 0
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 150%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 0
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.3
+max_print_speed = 60
+max_volumetric_speed = 0
+min_skirt_length = 2
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base]--h[layer_height]f[fill_density].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 3
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 5
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 20
+solid_infill_below_area = 50
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 150%
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 0
+support_material_threshold = 0
+thin_walls = 1
+threads = 4
+top_infill_extrusion_width = 80%
+top_solid_infill_speed = 75%
+top_solid_layers = 3
+travel_speed = 50
+xy_size_compensation = 0

Slic3r-Settings/print/-prusa-h04f30.ini

@@ -0,0 +1,86 @@
+# generated by Slic3r 1.2.9 on Sun Sep 13 21:25:36 2015
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 2
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 0
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 30%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_speed = 75%
+gap_fill_speed = 0
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 150%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 0
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.4
+max_print_speed = 60
+max_volumetric_speed = 0
+min_skirt_length = 2
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base]--h[layer_height]f[fill_density].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 5
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 0
+solid_infill_below_area = 50
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 150%
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 0
+support_material_threshold = 0
+thin_walls = 1
+threads = 4
+top_infill_extrusion_width = 80%
+top_solid_infill_speed = 0
+top_solid_layers = 3
+travel_speed = 50
+xy_size_compensation = 0

Slic3r-Settings/printer/-prusa-powerOff.ini

@@ -0,0 +1,27 @@
+# generated by Slic3r 1.2.9 on Sun Sep 13 21:43:09 2015
+bed_shape = 7x10,187x10,187x190,7x190
+before_layer_gcode = 
+end_gcode = G91     ; relative positioning\nG0 Z20  ; rise Z axis\nG90     ; turn absolute positioning back on\nG1 F3000 X190 Y195\n\nM104 S0 ; turn off temperature\nM84     ; disable motors\nM81     ; Power Supply off
+extruder_offset = 0x0
+gcode_flavor = reprap
+layer_gcode = 
+nozzle_diameter = 0.4
+octoprint_apikey = 
+octoprint_host = 
+pressure_advance = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 0
+retract_restart_extra = 0.1
+retract_restart_extra_toolchange = 0
+retract_speed = 7
+start_gcode = G1 F2000 X50 Y100 Z5 ; lift nozzle
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

Slic3r-Settings/printer/-prusa.ini

@@ -0,0 +1,27 @@
+# generated by Slic3r 1.2.9 on Sun Sep 13 22:24:18 2015
+bed_shape = 7x10,187x10,187x190,7x190
+before_layer_gcode = 
+end_gcode = G91     ; relative positioning\nG0 Z20  ; rise Z axis\nG90     ; turn absolute positioning back on\nG1 F3000 X190 Y195
+extruder_offset = 0x0
+gcode_flavor = reprap
+layer_gcode = 
+nozzle_diameter = 0.4
+octoprint_apikey = 
+octoprint_host = 
+pressure_advance = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 0
+retract_restart_extra = 0.1
+retract_restart_extra_toolchange = 0
+retract_speed = 7
+start_gcode = G1 F2000 X50 Y100 Z5 ; lift nozzle
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

Slic3r-Settings/slic3r.ini

@@ -0,0 +1,21 @@
+# generated by Slic3r 1.2.9 on Sun Sep 13 22:24:26 2015
+autocenter = 
+background_processing = 1
+last_output_path = /Users/jannik/Desktop
+last_version_check = 1442169415
+main_frame_maximized = 1
+main_frame_pos = 0,23
+main_frame_size = 1920,1025
+mode = expert
+remember_output_path = 1
+version = 1.2.9
+version_check = 1
+
+[presets]
+filament = -prusa-noBed.ini
+print = -prusa-h03f30.ini
+printer = -prusa.ini
+
+[recent]
+config_directory = /Users/jannik/JBeyerstedt-Projekte/reprap-prusa-i3
+skein_directory = /Users/jannik/JBeyerstedt-Projekte/reprap-prusa-i3/printTests