Slic3r-Settings/printer/-prusa-octolapse.ini

@@ -1,41 +0,0 @@
-# generated by Slic3r 1.3.1-dev on 2020-03-18 15:46:09
-bed_shape = 5x0,195x0,195x190,5x190
-before_layer_gcode = 
-between_objects_gcode = 
-end_gcode = G91 ;rel Pos\nG0 Z20\nG90 ;abs Pos\nG1 F3000 X190 Y190\n\nM104 S145 ;temp lower
-extruder_offset = 0x0
-gcode_flavor = reprap
-has_heatbed = 1
-host_type = octoprint
-layer_gcode = G4 P500; wait 500ms, trigger octolapse
-max_layer_height = 0.4
-min_layer_height = 0.2
-nozzle_diameter = 0.4
-octoprint_apikey = 
-pressure_advance = 0
-print_host = octoprusa.fra80
-printer_notes = 
-printer_settings_id = 
-retract_before_travel = 2
-retract_layer_change = 1
-retract_length = 1
-retract_length_toolchange = 10
-retract_lift = 0
-retract_lift_above = 0
-retract_lift_below = 0
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 7
-serial_port = 
-serial_speed = 250000
-start_gcode = G92 O ; pseudo gcode for octolapse homing\nG1 F2000 X50 Y100 Z5; start pos
-toolchange_gcode = 
-use_firmware_retraction = 0
-use_relative_e_distances = 0
-use_set_and_wait_bed = 0
-use_set_and_wait_extruder = 0
-use_volumetric_e = 0
-vibration_limit = 0
-wipe = 0
-z_offset = 0
-z_steps_per_mm = 0

Slic3r-Settings/printer/-prusa-timelapse.ini

@@ -1,13 +1,13 @@
 # generated by Slic3r 1.3.1-dev on 2020-03-18 08:57:51
 bed_shape = 5x0,195x0,195x190,5x190
-before_layer_gcode = ;Special layer change for octoprint\n;G92 E0; retract\n;G1 E-1; retract filament\nG1 X30 Y5 F5500\nG4 S0\nG4 P500\n;G1 E0; un-retract filament\n;[layer_z]
+before_layer_gcode = 
 between_objects_gcode = 
 end_gcode = G91 ;rel Pos\nG0 Z20\nG90 ;abs Pos\nG1 F3000 X190 Y190\n\nM104 S145 ;temp lower
 extruder_offset = 0x0
 gcode_flavor = reprap
 has_heatbed = 1
 host_type = octoprint
-layer_gcode = 
+layer_gcode = G1 X30 Y5 F5500\nG4 S0\nG4 P500\n;[layer_z]
 max_layer_height = 0.4
 min_layer_height = 0.2
 nozzle_diameter = 0.4
@@ -28,7 +28,7 @@ retract_restart_extra_toolchange = 0
 retract_speed = 7
 serial_port = 
 serial_speed = 250000
-start_gcode = G92 O ; pseudo gcode for octolapse homing\nG1 F2000 X50 Y100 Z5; start pos
+start_gcode = G1 F2000 X50 Y100 Z5; start pos
 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0