Slic3r-Settings/filament/-black-bedOff.ini

@@ -1,4 +1,4 @@
-# generated by Slic3r 1.3.1-dev on 2018-10-21 15:52:33
+# generated by Slic3r 1.3.1-dev on 2018-10-07 12:15:10
 bed_temperature = 0
 bridge_fan_speed = 100
 compatible_printers = 
@@ -9,8 +9,8 @@ extrusion_multiplier = 1
 fan_always_on = 0
 fan_below_layer_time = 30
 filament_colour = #000000
-filament_cost = 22
-filament_density = 1.24
+filament_cost = 0
+filament_density = 0
 filament_diameter = 2.9
 filament_max_volumetric_speed = 0
 filament_notes = ""

Slic3r-Settings/filament/-blue-bedOff.ini

@@ -1,25 +1,17 @@
-# generated by Slic3r 1.3.1-dev on 2018-11-24 12:57:44
+# generated by Slic3r 1.2.9 on Wed Nov 25 18:11:51 2015
 bed_temperature = 0
 bridge_fan_speed = 100
-compatible_printers = 
 cooling = 1
 disable_fan_first_layers = 1
-end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
-extrusion_multiplier = 1
+extrusion_multiplier = 1.05
 fan_always_on = 0
 fan_below_layer_time = 30
 filament_colour = #0080FF
-filament_cost = 22
-filament_density = 1.24
 filament_diameter = 3
-filament_max_volumetric_speed = 0
-filament_notes = ""
-filament_settings_id = 
 first_layer_bed_temperature = 0
 first_layer_temperature = 195
 max_fan_speed = 100
 min_fan_speed = 30
 min_print_speed = 10
 slowdown_below_layer_time = 20
-start_filament_gcode = "; Filament gcode\n"
 temperature = 195

Slic3r-Settings/print/-prusa-h03f15.ini

@@ -0,0 +1,86 @@
+# generated by Slic3r 1.2.9 on Sun Jun  5 17:01:31 2016
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 2
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 0
+brim_width = 0
+complete_objects = 1
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 18
+extruder_clearance_radius = 15
+extrusion_width = 0
+fill_angle = 45
+fill_density = 15%
+fill_pattern = honeycomb
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_speed = 60%
+gap_fill_speed = 10
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 150%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 0
+infill_speed = 80
+interface_shells = 0
+layer_height = 0.3
+max_print_speed = 70
+max_volumetric_speed = 0
+min_skirt_length = 2
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base]--h[layer_height]f[fill_density].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 2
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 5
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 15
+solid_infill_below_area = 50
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 125%
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 0
+support_material_threshold = 0
+thin_walls = 1
+threads = 4
+top_infill_extrusion_width = 90%
+top_solid_infill_speed = 80%
+top_solid_layers = 3
+travel_speed = 80
+xy_size_compensation = 0

Slic3r-Settings/print/-prusa-h03f30.ini

@@ -0,0 +1,86 @@
+# generated by Slic3r 1.2.9 on Sun Jun  5 17:01:25 2016
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 2
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 0
+brim_width = 0
+complete_objects = 1
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 18
+extruder_clearance_radius = 15
+extrusion_width = 0
+fill_angle = 45
+fill_density = 30%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_speed = 60%
+gap_fill_speed = 10
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 150%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 0
+infill_speed = 80
+interface_shells = 0
+layer_height = 0.3
+max_print_speed = 70
+max_volumetric_speed = 0
+min_skirt_length = 2
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base]--h[layer_height]f[fill_density].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 3
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 5
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 15
+solid_infill_below_area = 50
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 125%
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 0
+support_material_threshold = 0
+thin_walls = 1
+threads = 4
+top_infill_extrusion_width = 90%
+top_solid_infill_speed = 80%
+top_solid_layers = 3
+travel_speed = 80
+xy_size_compensation = 0

Slic3r-Settings/print/-prusa-h04f15.ini

@@ -0,0 +1,86 @@
+# generated by Slic3r 1.2.9 on Sun Jun  5 14:04:56 2016
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 2
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 0
+brim_width = 0
+complete_objects = 1
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 18
+extruder_clearance_radius = 15
+extrusion_width = 0
+fill_angle = 45
+fill_density = 15%
+fill_pattern = honeycomb
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.4
+first_layer_speed = 60%
+gap_fill_speed = 10
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 150%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 0
+infill_speed = 80
+interface_shells = 0
+layer_height = 0.4
+max_print_speed = 70
+max_volumetric_speed = 0
+min_skirt_length = 2
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base]--h[layer_height]f[fill_density].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 50
+perimeters = 2
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 5
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 15
+solid_infill_below_area = 50
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 125%
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 0
+support_material_threshold = 0
+thin_walls = 1
+threads = 4
+top_infill_extrusion_width = 90%
+top_solid_infill_speed = 80%
+top_solid_layers = 3
+travel_speed = 80
+xy_size_compensation = 0

Slic3r-Settings/print/prusa_auto-h03f15.ini

@@ -1,4 +1,4 @@
-# generated by Slic3r 1.3.1-dev on 2018-11-30 11:52:57
+# generated by Slic3r 1.3.1-dev on 2018-10-20 18:19:25
 adaptive_slicing = 0
 adaptive_slicing_quality = 75%
 avoid_crossing_perimeters = 0
@@ -14,7 +14,7 @@ complete_objects = 1
 default_acceleration = 0
 dont_support_bridges = 1
 external_perimeter_extrusion_width = 0
-external_perimeter_speed = 75%
+external_perimeter_speed = 40
 external_perimeters_first = 0
 extra_perimeters = 0
 extruder_clearance_height = 18
@@ -23,11 +23,11 @@ extrusion_width = 0
 fill_angle = 45
 fill_density = 15%
 fill_gaps = 1
-fill_pattern = rectilinear
+fill_pattern = honeycomb
 first_layer_acceleration = 0
-first_layer_extrusion_width = 150%
+first_layer_extrusion_width = 0
 first_layer_height = 0.3
-first_layer_speed = 50%
+first_layer_speed = 40
 gap_fill_speed = 0
 gcode_comments = 0
 infill_acceleration = 0
@@ -41,10 +41,10 @@ infill_speed = 0
 interface_shells = 0
 interior_brim_width = 0
 label_printed_objects = 0
-layer_height = 0.2
+layer_height = 0.3
 match_horizontal_surfaces = 0
-max_print_speed = 70
-max_volumetric_speed = 16
+max_print_speed = 80
+max_volumetric_speed = 40
 min_shell_thickness = 0
 min_skirt_length = 3
 min_top_bottom_shell_thickness = 0
@@ -56,7 +56,7 @@ overhangs = 1
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
-perimeter_speed = 35
+perimeter_speed = 0
 perimeters = 2
 post_process = 
 print_settings_id = 
@@ -64,11 +64,11 @@ raft_layers = 0
 regions_overlap = 0
 resolution = 0
 seam_position = aligned
-shortcuts = complete_objects;fill_density;fill_pattern;adaptive_slicing_quality;layer_height;seam_position;spiral_vase;adaptive_slicing;dont_support_bridges;support_material;raft_layers;support_material_buildplate_only
+shortcuts = complete_objects;fill_density;fill_pattern;seam_position;spiral_vase;adaptive_slicing;support_material
 skirt_distance = 5
 skirt_height = 1
 skirts = 1
-small_perimeter_speed = 35%
+small_perimeter_speed = 25%
 solid_infill_below_area = 50
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
@@ -98,7 +98,7 @@ support_material_threshold = 60%
 thin_walls = 1
 top_infill_extrusion_width = 0
 top_infill_pattern = rectilinear
-top_solid_infill_speed = 50%
+top_solid_infill_speed = 50
 top_solid_layers = 3
 travel_speed = 100
 xy_size_compensation = 0

Slic3r-Settings/printer/-prusa.ini

@@ -16,7 +16,7 @@ octoprint_apikey =
 pressure_advance = 0
 printer_notes = 
 printer_settings_id = 
-retract_before_travel = 2
+retract_before_travel = 1
 retract_layer_change = 1
 retract_length = 1
 retract_length_toolchange = 10

Slic3r-Settings/slic3r.ini

@@ -1,4 +1,4 @@
-# generated by Slic3r 1.3.1-dev on Fri Nov 30 12:52:57 2018
+# generated by Slic3r 1.3.1-dev on Sat Oct 20 20:31:31 2018
 autoalignz = 1
 autocenter = 
 background_processing = 1
@@ -7,12 +7,9 @@ invert_zoom = 0
 last_output_path = /Users/jannik/Desktop
 last_version_check = 1538910032
 main_frame_maximized = 
-main_frame_pos = 1,239
-main_frame_size = 1315,802
+main_frame_pos = 575,-157
+main_frame_size = 1291,836
 nudge_val = 1
-object_settings_maximized = 
-object_settings_pos = 230,91
-object_settings_size = 1000,700
 reload_behavior = 0
 reload_hide_dialog = 0
 remember_output_path = 1
@@ -27,10 +24,10 @@ overwrite = 1
 start = 
 
 [presets]
-filament = -black-bedOff
-print = prusa-default
+filament = -blue-bedOff
+print = prusa_auto-h03f15
 printer = -prusa
 
 [recent]
 config_directory = /Users/jannik/JBeyerstedt-Projekte/reprap-prusa-i3
-skein_directory = /Users/jannik/JBeyerstedt-Projekte/reprap-prusa-i3/printTests/Jolly3dPrintingTortureTest-#763622
+skein_directory = /Users/jannik/JBeyerstedt-Projekte/freecad/esp32-sensornode-case