slic3r: add printer profile for octolapse

Slic3r-Settings/printer/-prusa-octolapse.ini

@@ -0,0 +1,41 @@
+# generated by Slic3r 1.3.1-dev on 2020-03-18 15:46:09
+bed_shape = 5x0,195x0,195x190,5x190
+before_layer_gcode = 
+between_objects_gcode = 
+end_gcode = G91 ;rel Pos\nG0 Z20\nG90 ;abs Pos\nG1 F3000 X190 Y190\n\nM104 S145 ;temp lower
+extruder_offset = 0x0
+gcode_flavor = reprap
+has_heatbed = 1
+host_type = octoprint
+layer_gcode = G4 P500; wait 500ms, trigger octolapse
+max_layer_height = 0.4
+min_layer_height = 0.2
+nozzle_diameter = 0.4
+octoprint_apikey = 
+pressure_advance = 0
+print_host = octoprusa.fra80
+printer_notes = 
+printer_settings_id = 
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 1
+retract_length_toolchange = 10
+retract_lift = 0
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 7
+serial_port = 
+serial_speed = 250000
+start_gcode = G92 O ; pseudo gcode for octolapse homing\nG1 F2000 X50 Y100 Z5; start pos
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_set_and_wait_bed = 0
+use_set_and_wait_extruder = 0
+use_volumetric_e = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0
+z_steps_per_mm = 0

Slic3r-Settings/printer/-prusa-timelapse.ini

@@ -1,13 +1,13 @@
 # generated by Slic3r 1.3.1-dev on 2020-03-18 08:57:51
 bed_shape = 5x0,195x0,195x190,5x190
-before_layer_gcode = 
+before_layer_gcode = ;Special layer change for octoprint\n;G92 E0; retract\n;G1 E-1; retract filament\nG1 X30 Y5 F5500\nG4 S0\nG4 P500\n;G1 E0; un-retract filament\n;[layer_z]
 between_objects_gcode = 
 end_gcode = G91 ;rel Pos\nG0 Z20\nG90 ;abs Pos\nG1 F3000 X190 Y190\n\nM104 S145 ;temp lower
 extruder_offset = 0x0
 gcode_flavor = reprap
 has_heatbed = 1
 host_type = octoprint
-layer_gcode = G1 X30 Y5 F5500\nG4 S0\nG4 P500\n;[layer_z]
+layer_gcode = 
 max_layer_height = 0.4
 min_layer_height = 0.2
 nozzle_diameter = 0.4
@@ -28,7 +28,7 @@ retract_restart_extra_toolchange = 0
 retract_speed = 7
 serial_port = 
 serial_speed = 250000
-start_gcode = G1 F2000 X50 Y100 Z5; start pos
+start_gcode = G92 O ; pseudo gcode for octolapse homing\nG1 F2000 X50 Y100 Z5; start pos
 toolchange_gcode = 
 use_firmware_retraction = 0
 use_relative_e_distances = 0